Search Results

Recent investigations by others have indicated that the dynamic response of automotive brake rotors in the squeal frequency range involves the classic flexural modes as well as in-plane motion. While the latter set creates primarily in-plane displacements, there is coupling to transverse displacements that might produce vibrational instabilities. This question is investigated here by analyzing a modal model that includes two modes of the rotor and two modes of the pad and caliper assembly. Coupling between in-plane and transverse displacements is explicitly controlled. Results from this model indicate that the coupling does create vibrational instabilities. The instabilities, whose frequencies are in the squeal range, are characterized by power flow through the transverse motion of the rotor.

Drive shaft modelling effects frontal crash finite element simulation. A 35 mph rigid barrier impact of a body on frame SUV with an one piece drive shaft and a unibody SUV with a two piece drive shaft have been studied and simulated using finite element analyses. In the model, the drive shaft can take significant load in frontal impact crash. Assumptions regarding the drive shaft model can change the predicted engine motion in the simulation. This change influences the rocker @ B-pillar deceleration. Two modelling methods have been investigated in this study considering both joint mechanisms and material failure in dynamic impact. Model parameters for joint behavior and failure should be determined from vehicle design information and component testing. A body on frame SUV FEA model has been used to validate the drive shaft modeling technique by comparing the simulation results with crash test data.

A stochastic simulation based on the Monte-Carlo method was developed to re-target gap bulk density (GBD) in ceramic catalytic converters. The combined effect of manufacturing tolerances, shell spring back and thermal expansion was analyzed by this model. Shell spring back during the canning process was calculated using Finite Element Analysis (FEA). Thermal shell expansion was obtained using can deformation data from the Key-Life Test (KLT). An example of optimized GBD that provides a robust and manufacturable design is also presented.

While a Ni-MH battery has good performance properties, such as a high power density and no memory effect, it needs a powerful thermal management system to maintain within the required narrow thermal operating range for the 42V HEV applications. Inappropriate battery temperatures result in degradation of the battery performance and life. For the battery cooling system, air is blown into the battery pack. The exhaust is then vented outside due to potential safety issues with battery emissions. This cooling strategy can significantly impact fuel economy and cabin climate control. This is particularly true when the battery is experiencing frequent charge and discharge of high-depths in extreme hot or cold weather conditions. To optimize performance and life of HEV traction batteries, the battery cooling design must keep the battery operation temperature below a maximum value and uniform across the battery cells.

A Variable Displacement Engine (VDE) improves fuel economy by deactivating half the cylinders at light load. The actual fuel economy benefit attained in the vehicle depends on how often cylinders can be deactivated, which is a function of test cycle, engine size, and vehicle weight. In practice, cylinder deactivation will also be constrained by NVH (noise, vibration, and harshness). This paper presents fuel economy projections for VDE in several different engine and vehicle applications. Sensitivity to NVH considerations is quantified by calculating fuel economy with and without cylinder deactivation in various operating modes: idle, low engine speed, 1st and 2nd gear, and warm-up after cold start. The effects of lug limits and calibration hysteresis are also presented.

Machining fixtures are used to locate and constrain a workpiece during a machining operation. To ensure that the workpiece is manufactured according to specified dimensions and tolerances, it must be appropriately located and clamped. Minimizing workpiece and fixture tooling deflections due to clamping and cutting forces in machining is critical to the machining accuracy. An ideal fixture design maximizes locating accuracy and workpiece stability, while minimizing displacements. The purpose of this research is to develop a method for modeling workpiece boundary conditions and applied loads during a machining process, analyze modular fixture tool contact area deformation and optimize support locations, using finite element analysis (FEA). The workpiece boundary conditions are defined by locators and clamps. The locators are placed in a 3-2-1 fixture configuration, constraining all degrees of freedom of the workpiece and are modeled using linear spring-gap elements.

Sliding door designs are applied to rear side doors on vans and other large vehicles with a trend towards dual sliding doors with power operation. It is beneficial for the vehicle user to reduce the weight of and space occupied by these doors. Alcoa, in conjunction with Ford, has developed a multi-product, multi-material-based solution, which significantly reduces the cost of an aluminum sliding door and provides both consumer delight and stamping-assembly plant benefits. The design was successfully demonstrated through a concept readiness/technology demonstration program.

The evaluation of the performance benefits of solar load reducing glazings using production vehicles is key to the establishment of the product cost/benefit ratio. Climatic windtunnels normally used to evaluate heat gain and vehicle cooldown can not provide true solar simulation. Comparative testing using a test car and a control vehicle must therefore be conducted outside in uncontrollable ambient conditions. The subject paper deals with the development of a testing methodology capable of quantifying thermal performance differences, as low as 5%, resulting from component differences, including glazings. The procedure described includes the use of B & K Thermal Comfort Meters to standardize the refrigeration system performance and to evaluate the rate of vehicle interior cooldown. Data taken during summer test programs in the Southwest for evaluation of heat absorbing glazings will be reviewed.

Pump whine as well as other NVH issues related to power steering system can become customer concerns at the vehicle level. In order to avoid that, proposed treatment of the pump structure and its installation on the engine should be performed. This is particularly important because most vane pumps have a wide range of excitation that can reach 1000 Hz (30th order @ 6000 rpm). This requires maximizing the ‘as installed’ frequencies of the pump to avoid coincidence with the engine and other FEAD harmonics.

Piston slap is a problem that plagues many engines. One of the most difficult aspects of designing to eliminate piston slap is that slight differences in operating conditions and in part geometries from build to build can create large differences in the magnitude of piston slap. In this paper we will describe a design for robustness CAE approach to eliminating piston slap. This approach considers the variations of the significant control factors in the design, e.g. piston pin offset, piston skirt design, etc. as well as the variation in the noise factors the system is subjected to, e.g. assembly clearance, skirt collapse, peak cylinder pressure, cylinder pressure rise rate, and location of peak cylinder pressure. Using analytical knowledge about how these various factors impact the generation of piston slap, a piston design for low levels of piston slap can be determined that is robust to the various noise factors.

Exhaust valve temperatures are important in the selection of valve materials, and have strong effects on borderline spark angle and pre-ignition borderline limit. In order to support analytical modeling of exhaust valve temperatures and to correlate exhaust valve temperatures as a function of engine Reynolds number, exhaust valve temperatures were mapped as a function of spark angle and engine coolant temperatures at 2000 rpm. In addition temperatures were measured at wide open throttle at 2000, 3000, and 4000 rpm. The exhaust valve temperature was expressed as a dimensionless temperature using the exhaust gas temperature and the engine coolant temperature, then the dimensionless temperature was correlated as a function of spark angle and engine Reynolds number. The results indicate that once the temperature is known at a given speed and load condition for any one cylinder, the temperature at other speed and load conditions can be reasonably estimated.

The pneumatic air brake system for heavy commercial trucks is composed by a large number of components, aiming its proper work and compliance with rigorous criteria of vehicular safety. One of those components, present along the whole vehicle, is the air brake tube, ducts which feed valves and reservoirs with compressed air, carrying signals for acting or releasing the brake system. In 2011, due to a lack of butadiene in a global scale, the manufacturing of these tubes was compromised; as this is an important raw material present on the polymer used so far, PA12. This article introduces the methodology of selecting, developing and validating in vehicle an alternative polymer for this application. For this purpose, acceptance criteria have been established through global material specifications, as well as bench tests and vehicular validation requirements.

Imposing tensile stress on an edge of a sheet metal blank is a common condition in many sheet metal forming operations, making edge formability a very important factor to consider. Because edge formability varies greatly among different materials, cutting methods (and their control parameters), it is very important to have access to an experimental technique that would allow for quick and reliable evaluation of edge formability for a given case. In this paper, two existing techniques are compared: the hole expansion test and the tensile test. It is shown that the hole expansion test might not be adequate for many cases, and is prone to overestimating the limiting strain, because the burr on the sheared edge is typically smaller than what is observed in production. The tensile test represents an effective alternative to the hole expansion test. Advantages and disadvantages of each case are discussed.

The main objective of the current paper was to investigate the fluid flow and pressure loss characteristics of DPF substrates with asymmetric channels utilizing 3-D Computational Fluid Dynamics (CFD) methods. The ratio of inlet to outlet channel width is 1.2. First, CFD results of velocity and static pressure distributions inside the inlet and outlet channels are discussed for the baseline case with both forward and reversed exhaust flow. Results were also compared with the regular DPF of same cell structure and wall material properties. It was found that asymmetrical channel design has higher pressure loss. The lowest pressure loss was found for the asymmetrical channel design with smaller inlet channels. Then, the effects of DPF length and filter wall permeability on pressure loss, flow and pressure distributions were investigated.

The article presents an innovative approach to the implementation of a robust design optimization solution in an automobiles assembly process. The approach of the entire project is specific to the 6 Sigma optimization process, by applying the DMAIC cycle integrated in a robust engineering approach for rendering lean the final product assembly process. According to the improvement cycle, the aspects specific for such a process are presented sequentially starting with the “Define” phase for presenting the encountered problem and continuing with the presentation of the scope of the project and its objectives. The “Improvement” cycle phase is applied by the analysis of the monitored 6 Sigma metrics (defined during the previous “Measure” phase and the cause and effect analysis, done during a brainstorming meeting developed during the “Analyze” phase). There follows a proposal for the innovative robust solution by which the assembly process is optimized.

The development of embedded systems in automotive environment has brought a strong expansion in the number of applications dependent of programmable devices. A failure in any of these systems may cause different types of damages. Therefore, it requires a high confidence in their operation. Many of these faults are inserted during the coding process. A tool for formal verification of the implemented code could allow the detection of possible errors that could not be encountered during the testing phase. In this paper, we propose a method for verifying software from the reduced model of the software built automatically with information from multiple traces of program executions. To illustrate the application of the proposed method a case study for an automotive electronic module that controls the windshield wiper is presented.

This article is a new methodology to create a strong and reliable procedure to measure oil level at dealers. Most of time, commercial trucks run full loaded. Engine oil level indication systems are designed to measure oil level at that condition. However commercial trucks are assembled and sold empty and without bodies for trucks. In result of this condition, vehicles with a false indication of low engine oil level are detected at dealers' pre-delivery inspection, resulting in oil addition. This oil addition causes unnecessary costs, since vehicles are produced with maximum oil level. The methodology presented in this study analyzes and treats all variables involved in engine oil level measurements from engine production line until dealers' pre-delivery inspection

Typical automotive body structures use resistance spot welding for most joining purposes. New materials, such as Advanced High Strength Steels (AHSS) are increasingly used in the construction of automotive body structures to meet increasingly higher structural performance requirements while maintaining or reducing weight of the vehicle. One of the challenges for implementation of new AHSS materials is weldability assessment. Weld engineers and vehicle program teams spend significant efforts and resources in testing weldability of new sheet metal stack-ups. In this paper, we present a methodology to determine the weldability of sheet metal stack-ups using an Artificial Neural Network-based tool that learns from historical data. The paper concludes by reviewing weldability results predicted by using this tool and comparing with actual test results.

A demonstration structure was cast in AM60. The structure, known as the Generic Frame Casting or GFC, was designed specifically to mimic features seen in castings for closure applications. Excised samples were subsequently removed from different areas of the casting and tested under axial loading conditions. Component level tests were also conducted. Comparison of the excised sample results and the component level testing indicated the influence of local properties on the component level deformation. It was shown that varying the casting processing conditions could change the local ductility and yield strength in different areas of casting with the same geometry. Lowering the local ductility decreased the total displacement in a component level test and lowered the amount of energy absorption. Therefore, understanding the processing conditions and their influence on the local properties is important for predicting behavior in a component level test.

Frames are important structures found in many transportation applications such as automotive bodies and train cars. They are also widely employed in buildings, bridges, and other load bearing designs. When a frame is carrying multiple loads, it can potentially risk a catastrophic buckling failure. The loads on the frame may be non-proportional in that one force stays constant while the other is increased until buckling occurs. In this study the buckling problem is formulated as a constrained eigenvalue problem (CEVP). As opposed to other CEVP in which the eigenvectors are forced to comply with a number of the constraints, the eigenvalues in the current CEVP are subject to some equality constraints. A numerical algorithm for solving the constrained eigenvalue problem is presented. The algorithm is a simple trapping scheme in which the computation starts with an initial guess and a window containing the potential target for the eigenvalue is identified.